Mercruiser Alpha1 gen 1 & Bravo Ram shaft pin 1983/up Polished ring & drive

Description

Mercruiser Alpha1 gen 1 & Bravo Ram shaft pin 1983/up Polished ring & drive
Ring and drive mounting shafts/pins/anchors with black rubber
grommets
, nuts and washers! As Pictured.
Alpha One Generation One & Bravo only! Over all length without threads is 10" and with threads 12" The drive shaft is 7.5" without threads and about 9" with threads. These are 7/16" diameter so double check your black Groumets.
These are a set of (2) front and rear. 1 for the gimbal ring and the shorter one is for the tail of the drive.
Mercruiser Alpha One Generation One Ram shaft pin 1983 and up. Used, polished, Threads chased as needed. For the serial numbers 98703 98704 14034-1 14035-1 98703-1 98704-1 OEM Stainless steel. Most have new or good used lock nuts.
These will work on Alpha One Generation One & Bravo!
Call or message me with any questions. Tech support is as always 100% free. My name is Mike!
I stand behind all my items to a point that if I make a mistake I pay all shipping to make it right and all I ask is if you make a mistake and buy the wrong rams you pay the extra shipping to make it right! I try my best not to make any mistakes but I am not perfect no matter how hard I try. Message me or send me pictures. I can pretty much Identify any Mercruiser gimbal/hydraulic or exhaust part made.
Don't forget to check my e-bay store for many other Mercruiser pumps, hydraulic lines, rams, cylinders, exhaust pipes & gimbals’!
The easiest way to find your items is enter my store and choose a category on the left!
If these develop a leak in the next few years I will replace a ram with no charge. You just pay shipping back to me and I pay to return you a non-leaking ram.
Message me if you need a set of ram shafts, washers, rubbers & nuts. But they may be in another sale in my e-bay store.
These are 4.9 out of 5 star! And I will stand behind them!
But I would
Appreciate a 5 star rating when they arrive as discribed!
If you don’t see shipping amount message me for international shipping quote.
Tips
By the way Great news, eBay has taken over the
Resolution Center
and when you buy you are safer. EBay is even charging the seller return shipping and you get all your money back for junk that was listed as good working order.
Here is a hint for you, most of the states are fine for buying boat parts but try and stay away from Florida! 80% of my eBay purchases from Florida of used boat parts are bad and must be returned.
Here is a hint for buying pumps on e-bay, if in the item description it states untested, unknown, no way of testing, don't know how to test or has not been tested you can count on it is junk! Also people selling pumps on e-bay will state pump is guaranteed to work perfectly, The pump could be working perfectly but that does not mean that the motor works at all or that the solenoids are good. Or they will state that the motor works perfectly but that does not mean the reservoir isn’t cracked or that the pump is good is any good or even that the threads for the lines are not stripped out. I buy these pumps on e-bay all the time and on the average it takes two pumps to make one! You should never pay over for a used pre-alpha pump on e-bay or over for a used Alpha/bravo pump on e-bay because odds are that you will have to spend about 0 to get the pump you bought working correctly.
I buy these pumps on e-bay and in bulk all the time. My point is that about 95% of the pumps I get have issues. Bad motor, bad solenoids, incorrectly wired or just all gummed up inside the reservoir. Let’s face it people sell there junk on e-bay. Buy from me and you only have to buy one replacement.
Payment methods accepted are
Paypal Preferred
Visa / MasterCard
Discover
American Express
Receive payment upon pickup
I also accept credit cards over the phone if you don't have an online payment method.
The threads are all checked and rechecked 5 times and then checked again before shipping to be sure the line threads are good. Before you even think about installing the rams or taking the rams to have them installed look at the threads because stripped out threads are not covered under warrantee! Finger tighten 2 complete turns in first before using a wrench. (Hint) Also double check the lines you are using on the rams and make sure the threads are good on the lines, sometimes when removing lines from old rams you can tear out the old threads from the old rams and have them stuck in the lines and then when you try installing the lines in good threaded rams you can strip out the good line threads. Basically check all threads male and female on both rams and lines!