Mercruiser Transom Bellows Kit Gimbal Alpha 1 ONE SHIFT CBL U-JOINTS HINGE PIN T

Description

SquareTrade © AP6.0
THIS IS A VERY UNUSUAL WAY TO START OFF THE DESCRIPTION OF THIS KIT - BUT --- HERE GOES:
PLEASE DO NOT BUY THIS KIT UNLESS YOU ARE CERTAIN ABOUT WHAT DRIVE IT IS THAT YOU HAVE
!!
(You will receive a Sierra
Hinge Pin Tool
with this kit)
THE ALPHA ONE DRIVE AND THE ALPHA ONE, GEN 2 DRIVE
ARE
VERY DIFFERENT OUTDRIVES
.
THIS KIT
DOES NOT FIT
THE ALPHA ONE, GEN 2 OUTDRIVE
THIS KIT
DOES NOT FIT
THE ALPHA ONE, GEN 2 OUTDRIVE
THIS KIT
DOES NOT FIT
THE ALPHA ONE, GEN 2 OUTDRIVE
I HAVE TO BE VERY CLEAR ABOUT THIS TO SAVE BOTH YOU AND I LOTS OF POTENTIAL TROUBLES.
IF YOU DO NOT KNOW WHAT OUTDRIVE IT IS THAT YOU HAVE, IT IS IMPERATIVE THAT YOU FIND OUT. YOU WILL NEED TO KNOW YOUR
OUTDRIVE
SERIAL NUMBER AND THEN CHECK IT WITH THE CHART BELOW.
MERCURY PARTS GETTING FACTS, TO MAKE LIFE SIMPLER
:
1) MERCURY DOES NOT RECOGNIZE WHAT BOAT IT IS THAT YOU HAVE.
2) MERCURY DOES NOT RECOGNIZE THE YEAR OF YOUR OUTDRIVE OR ENGINE - FOR PARTS GETTING PURPOSES.
3) MERCURY BASES ALL PARTS GETTING ON SERIAL NUMBERS ONLY
4) MERCURY UNFORTUNATELY NEVER PRODUCED A DECAL OR STICKER THAT SHOWS "COMMA GEN 2" (ALPHA ONE, GEN 2).  ******MERCURY'S ALPHA ONE OUTDRIVE AND THEIR ALPHA ONE GEN 2 OUTDRIVES BOTH HAD ONLY AN "ALPHA ONE" DECAL SHOWN ON THEIR OUTDRIVES****.  HERE IS WHAT MERCURY DIDN'T DO WHEN THEY STARTED PRODUCING THE ALPHA ONE, GEN 2 OUTDRIVE, SOMETIME IN 1991: THEY DID NOT PRODUCED A "COMMA GEN 2" ADDITIONAL DECAL TO ADD TO "ALPHA ONE" THAT IS SHOWN ON THEIR OUTDRIVES - THIS WOULD HAVE BEEN VERY HELPFUL TO STOP THE CONFUSION ABOUT WHAT OUTDRIVE IT IS.
THREE SERIAL NUMBERS TO BE CONCERNED WITH
:
1)
OUTDRIVE SERIAL NUMBER
(SOME CALL IT DRIVE SERIAL NUMBER) NEEDED TO GET OUTDRIVE PARTS (THE OUTDRIVE CONSISTS OF THE UPPER GEARCASE AND THE LOWER UNIT).
2)
ENGINE SERIAL NUMBER
(IF YOU NEED ENGINE PARTS)
3)
TRANSOM SERIAL NUMBER
(LESS IMPORTANT - BUT RECORD THIS NUMBER).
WHEN YOU FIND THESE THREE SERIAL NUMBERS, PUT THEM IN PLASTIC AND KEEP THEM IN YOUR WALLET, BECAUSE LIFE WITH A MERCURY PRODUCT WILL BE MUCH EASIER.
WHERE ARE THESE SERIAL NUMBERS LOCATED ON YOUR UNIT??  GOOGLE:  "MERCRUISER SERIAL NUMBER LOCATE"
AFTER YOU FIND YOUR OUTDRIVE SERIAL NUMBER - THEN YOU CAN LOOK AT THE TWO CHARTS BELOW TO SEE IF YOU HAVE EITHER:
1) AN ALPHA ONE OUTDRIVE
OR
2) AN ALPHA ONE, GEN 2 OUTDRIVE
REMEMBER, THIS KIT
WILL NOT FIT THE ALPHA ONE, GEN 2 OUTDRIVE
.
THIS IS A KIT FOR THE ALPHA ONE OUTDRIVE
.
R/MR/ALPHA ONE (Sterndrive) 1983-1990
Click on Serial number
ALPHA ONE (GEN.II) 1991-1995
Click on Serial number
ALPHA ONE (GEN.II) 1996-1997
Click on Serial number
0F680000 THRU 0K999999
ALPHA ONE (GEN.II) 1998 AND UP
Click on Serial number
0L100040 & Up
++++YOU WILL RECEIVE THE
SHIFT CABLE AND HARDWARE
AND
U-Joints
and
BELLOWS ADHESIVE TOO!!
- SEE  PICTURE
THIS IS A TRANSOM OUTDRIVE BELLOWS KIT FOR MERCRUISER OUTDRIVES - ALPHA ONE (1983-1991) and #1 DRIVES (1973-1984). IF YOUR ARE NOT SURE OF WHICH DRIVE YOU HAVE - E-MAIL ME AND I'LL RESPOND PROMPTLY:  jhall  019 at sign Verizon  .   net (THE GEN 2'S STARTED WITH OUTDRIVE SERIAL NUMBER OD469859 AND UP)
EARLIER DRIVE THAN 1973? E-MAIL ME AND WE'LL FIGURE IT OUT TOGETHER.
TR/TRS DRIVE??
- THIS KIT WILL NOT WORK, BUT I'LL BE GLAD TO HELP YOU WITH THE CORRECT PARTS FOR THOSE BOATERS WITH THE TR/TRS DRIVES.
+++++++ INCLUDES TWO STANDARD U-JOINTS AND
BELLOWS ADHESIVE
++++++++
THIS AFTERMARKET KIT INCLUDES A
SIERRA
or
GLM
GIMBAL BEARING (REPLACES MERCURY # 30-60794A4),
AND
A
SIERRA
OUTDRIVE GASKET SET THAT INCLUDES THE DRIVE-SHAFT HOUSING TO THE BELL HOUSING GASKET, THE BELL HOUSING GASKET
AND
3 O-RINGS. THE OUTDRIVE GASKET SET REPLACES MERCURY PART NUMBER 27-64818A3
AND
27-94996Q2.  IN ADDITION, YOU WILL RECEIVE ALL THREE BELLOWS,
ALSO SIERRA
, WITH STAINLESS STEEL CLAMPS - SHIFT BELLOWS (REPLACES MERCRUISER 74639 and INCLUDES CLAMPS - NOT TIE WRAPS!), U-JOINT BELLOWS      (REPLACES 60932A4 "RIDGED"), AND EXHAUST BELLOWS (32734A3 AND 18654A1).  ALSO, YOU GET
TWO QUALITY CONTINENTAL WATER HOSES, FORMERLY
GOODYEAR
(NOT HEATER HOSE THAT WILL BEND TOO EASILY) - 32-32461 AND 32-41725-33.  2 HOSES BECAUSE MERCURY USED 3/4 INCH AND 5/8 INCH.  THIS WAY YOU WON'T HAVE TO WORRY ABOUT WHICH ONE YOU HAVE.
REMEMBER, THIS KIT INCLUDES 2 STANDARD U-JOINTS!  IF YOU NEED HD U-JOINTS (RUNNING MORE THAN 260hp) THEN YOU WILL NEED TO CONTACT ME FOR PRICING.  HD U-JOINTS ARE SLIGHTLY LONGER, BUT ARE OF THE SAME CAP SIZE.  HD U-JOINTS,
IF YOU NEED THEM
, WILL ADD ABOUT TO THE PRICE OF THIS KIT.
THE U-JOINTS WILL SHOW "MADE IN CHINA" ON THEM.
*******************YOU WILL NEED A HINGE PIN TOOL TO START THIS JOB  - .00 IF YOU NEED IT**********************
IF YOU WOULD LIKE INFO ON OTHER MARINE ITEMS  jhall 019  Verizon  dot  net,
ALL
PAR
TS
IN THIS
KIT
ARE, OF COURSE,
BRAND
NEW
IN THE
BOX
! HAPPY BIDDING!! WE HAVE MANY OTHER MARINE PAR
TS
AND
SHOP
MANUALS FOR OUTBOARDS
AND
STERNDRIVES. VERY QUICK PRIORITY MAIL SHIPPING!!